AK-Build Tools

AK-Builder riveting press, black-finished, showing main unit, assorted dies and supports.

In Stock

$270⁰⁰

+ −

The AK-Builder Riveting Tool is the proven standard for precision AK builds. It installs front and rear trunnion rivets, center supports, and scope rails with perfect alignment and professional results — crafted from heat-treated 4140 steel and trusted by builders worldwide. (Does not install trigger guard rivets.)

AK-Builder Barrel Press Kit

0.0

In Stock

$139⁹⁵

+ −

Choose the ram size of your press in the drop down box below. The 1" and 1.6" ram pieces are machined on a lathe from bar stock then black oxided. The 1.6" ram is for the new grey or orange 20 ton Harbor Freight shop press. The 1" is for their gray 12 ton. ...

Ram Adapter Size1.6" Ram Add $7.50

AK-Builder Flat Bending Die Set

0.0

In Stock

$219⁹⁵

+ −

AK-Builder Flat Bending Die Set A heavy-duty die set built for forming AK receiver flats in 1.0 mm , 1.5 mm , and Chinese variants (when the correct punch is used). The base starts as a solid 17 lb steel block and is precision machined down to about 14.5 lb, giving it the strength and...

OptionsMAK90 Punch

AK Trunnion Rivet Hole Drilling Fixture

0.0

In Stock

$99⁹⁵

+ −

Here is a professional tool for drilling the front and rear trunnion holes in AK47 receivers. This tool will work with 7.62 and 5.45 trunnions using two different expanding mandrels that fit into the trunnion. The red mandrel fits the 7.62 and the blue fits the 5.45. The...

AK-Builder Trigger Guard Riveting Jig, black oxide finish, with detached components.

AK47 Trigger Guard Riveting Jig

0.0

In Stock

$85⁰⁰

+ −

Installs all five trigger guard rivets with precision—front four at once, rear separately. Magnetic rear support and an adjustable/removable rear block fit multiple AK variants; compatible with receivers that already have center support and rails.

AK-Builder black oxide AKM receiver drilling fixture kit, with included drill bits and supports.

AK-Builder Receiver Blank Drilling Fixture

0.0

In Stock

$139⁹⁵

+ −

AK-BUILDER Receiver Blank Drilling Fixture This tool is designed to be used with 80% AKM receivers with OR without rails and center supports installed. The bottom of the fixture is also setup to be used if your receiver has trigger humps or a reinforcement plate. The fixture is...

TypeV-5 Standard or Underfolder-Sidefolder Plates

Spot Welder Tong

0.0

In Stock

$45⁹⁵

+ −

This spot welder tong is designed to work with the Harbor Freight #45689 welder or 61205-61206 if you get the extended tip . Avoid the 220v welder if at all possible due to the possibility of burn through while welding. The tong will come with a screw-on tip that can be replaced...

Angled view of AK-Builder steel Rail Alignment Fixture showing front clamp and screw.

AK-Builder Rail Alignment Fixture

0.0

In Stock

$29⁹⁵

+ −

AK-Builder rail alignment fixture — positions and clamps lower bolt guide rails in stamped receivers for accurate welding and alignment.

Rivet Head Drilling Tool

0.0

In Stock

$37⁹⁵

+ −

Rivet head drilling tool — heat-treated steel, includes 5/32" drill bit. Designed for removing trunnion rivets from AK parts kits.

AKM Trunnion Support Block

0.0

In Stock

$34⁹⁵

+ −

Support plate for pressing in or out your barrel pins on an AKM style trunnion. These are not specifically made for use with any of the bulged trunnion 1.5mm receivers. These are made from 6061 T6 aluminum then black anodized. Comes with three set screws for leveling the trunnion if...

PSL Brass Barrel Press Puck

0.0

Out-of-stock

$9⁹⁵

The PSL Brass Barrel Press Puck is used to press the PSL barrel out of the front trunnion. DO NOT use the other brass nut we sell for the other barrels we offer. Doing so will ruin the chamber end of the PSL barrel.

MILLED Receiver Drilling Fixture V2

0.0

In Stock

$119⁹⁵

+ −

AK-BUILDER Milled Receiver Drilling Fixture This tool is made specifically for the AK-BUILDER 80% Milled Receivers. We can not guarantee this fixture to work with milled receivers made by other manufacturers. The fixture is machined, case hardened, black oxided and then laser...

Top-down view of anodized AK-Builder Yugo M72 front sight/gas block pin removal block.

Yugo M72 Front Sight/Gas Block Retainer Pin Removal Block

0.0

Out-of-stock

$59⁹⁵

Here is a tool that we have been using to demill and populate our parts kits. This is made to support the gas block and front sight while removing or installing the pins. The block is anodized and then laser engraved showing how the gas block or sight sits on the...

AK-Builder 2.5mm black oxided punch set, starter and long tools.

2.5mm Punch Set

0.0

In Stock

$27⁹⁵

+ −

We designed these punches for demilling parts kits in our shop and use them daily. These can be bought as a set or individually. The problem with buying regular punches is that you have to cut them down to make a starter punch to get the 2mm pins to start moving. Once...

Angled view of AK-Builder 2.5mm black oxided punch with hex head, for Yugo pins.

2.5mm Punch

0.0

In Stock

$14⁹⁵

+ −

This punch is used for the 2.5mm pins on yugo gas blocks and front sights. We designed these punches for demilling parts kits in our shop and use them daily. These can be bought as a set or individually. The problem with buying regular punches is that you have to cut them...

Angled view AK-Builder 2.5mm black oxided tool steel starter punch with hex head.

2.5mm Starter Punch

0.0

In Stock

$14⁹⁵

+ −

This punch is used for the 2.5mm pins on yugo gas blocks and front sights. We designed these punches for demilling parts kits in our shop and use them daily. These can be bought as a set or individually. The problem with buying regular punches is that you have to cut them...

AKFST-10 Mini Beryl Elevation Tool

0.0

Out-of-stock

$19⁵⁰

Elevation tool for Mini Beryl AK pistols. The Mini Beryl is unique because the sight post is square which is why this special tool is required. The other end of the tool is made to help push pins out on the AK. All steel, precision CNC machined, hardened, and zinc plated. Made in the...

Thread Size14x1mm LH